International Awlcraft 4L


or 4 payments of $38.75 with Afterpay

Available in red, blue or black, 4L

SKU: N/A Category: Tags: ,


A general purpose high strength ablative cuprous oxide antifouling with minimal build up due to self polishing technology.
* Good protection for heavy fouling areas
* For use on fiberglass, wood and primed underwater metals (except aluminum)
* Quick drying
Colour YBE000-Blue, YBE001-Red , YBE002-Black
Finish Light sheen
Specific Gravity 1.6
Volume Solids 48%
VOC (As Supplied) 400 g/lt
Unit Size 4 lt
5°C (41°F) 15°C (59°F) 23°C (73°F) 35°C (95°F)
Immersion 24 hrs 12 hrs 6 hrs 3 hrs
Touch Dry 1 hrs 45 mins 30 mins 20 mins
Note: Max. Immersion Times are as follows: 5-15°C – 3 mths; 23°C – 2 mths; 35°C – 1 mth
Substrate Temperature
5°C (41°F) 15°C (59°F) 23°C (73°F) 35°C (95°F)
Overcoated By Min Max Min Max Min Max Min Max
Awlcraft Antifouling 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext
Preparation All substrates must be clean, dry and free from contaminants. All surfaces should have been primed with the
appropriate primers. Suggested primers: Interprotect (two pack) or Primocon (single packs).
Method Apply 2 coats per season on the hull. 3 coats are required on the leading and trailing edges, waterline, rudder and keel.
This is important for best performance.
Hints Thinner YTA085 International Antifouling Thinners #3.
Thinning Do not thin unless absolutely necessary. If thinning is necessary, do not thin more than 10% by volume.
Cleaner YTA085 International Antifouling Thinners #3.
Ventilation and Humidity Control Ensure adequate ventilation during use.
Airless Spray Pressure: 176-210 bar. Tip Size: 2180.
Other For Airmix spray application – Pressure: 2.5 bar. Tip Size: 20-113. True colour will develop after immersion. For in
season maintenance wipe surface with a soft sponge or equivalent. Heavy cleaning operations on a regular basis may
remove some paint leading to a reduction of the in-service life of the coating. To prevent premature failure, ensure
correct amount of paint is applied using the coverage as a guide.
Some Important Points Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces.
Product temperature should be minimum -5°C and maximum 35°C.
Ambient temperature should be minimum -5°C and maximum 35°C.
Substrate temperature should be 3°C/5°F above dew point and maximum 35°C/95°F.
Compatibility/Substrates GRP, Wood, Steel/Iron, Lead. Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces.
Number of Coats 1-2
Coverage (Theoretical) – 6 m²/lt
(Practical) – 5.4 m²/lt by brush, 3.2 m²/lt by spray.
Recommended DFT per coat 80 microns dry
Recommended WFT per coat 167 microns wet
Application Methods Airless Spray, Airmix, Brush, Roller
Awlcraft Antifouling
Self Polishing Antifouling
Please refer to your local representative or visit for further information.

Antifoulings should only be wet sanded. Never dry sand or burn-off old antifoulings. Always use gloves and goggles
and keep skin protected with overalls. Contains biocides. Users should ensure they have a copy of the Material Safety
Datasheet for this product and that they are familiar with all the safety directions before use.

Additional information

Choose Colour

Black, Blue, Red


There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.